Qumtrix / BASE-X5A / Datasheet & hardware manual
BASE-X5A datasheet and hardware manual
Dual-role base/rover RTK GNSS module with industrial IMU · QM5002B · Rev 1.0 · 13 pages
The datasheet and hardware manual for BASE-X5A (QM5002B), the dual-role RTK module that runs either as a local base station broadcasting RTCMv3 corrections or as a rover consuming CORS corrections over NTRIP. It documents the multi-constellation engine, the industrial IMU fusion, the interference and multipath mitigation, the micro-USB, Ethernet and 3.3 V TTL UART interfaces, the complete 20-pin UART header map, and the timing and event synchronisation. Every table is reproduced below; the PDF is the same document for print.
What this manual covers
BASE-X5A is a dual-role positioning module: the same board runs as a local base station broadcasting RTCMv3 corrections, or as a rover consuming CORS corrections over NTRIP. Both roles share one multi-constellation engine that tracks GPS, GLONASS, Galileo, BeiDou and QZSS across L1/L2/L5 and holds RTK-Fixed status while the machine is moving.
Integration is deliberately open: observation and correction data leave the module as NMEA-0183, SBF or RTCM, and micro-USB (two virtual COM ports plus Ethernet), Ethernet and multiple 3.3 V TTL UARTs connect straight to flight controllers and industrial MCUs. An industrial-grade IMU with dynamic sensor fusion keeps heading and position usable when satellites drop out, wide-band interference mitigation with three automatic notch filters suppresses RF noise, and configurable 1PPS plus external event triggers time-stamp position snapshots for multi-sensor alignment.
Key figures at a glance
| Item | Value |
|---|---|
| Model | BASE-X5A (QM5002B) |
| Constellations | GPS · GLONASS · Galileo · BeiDou · QZSS · SBAS · IRNSS |
| Positioning modes | StandAlone · DGPS · SBAS · RTK (base/rover) · PPP |
| Interfaces | Micro-USB (2 virtual COM + Ethernet) · 3.3 V TTL UART · MMCX · TF card · PPS/event |
| Data formats | NMEA-0183 · RTCM v2/v3 · SBF (convertible to RINEX, ASCII, KML) |
| Timing | Configurable 1PPS, selectable GNSS time reference, external event inputs |
| Interference | Wide-band mitigation, 3 automatic notch filters, code and carrier multipath suppression |
| Configuration | Web UI at 192.168.3.1 · RxControl · command line · persistent boot configuration |
Contents of the manual
| Section | Page |
|---|---|
| 1. Introduction summary | 4 |
| 2. Product overview and technology | 5 |
| 3. Technical data and specifications | 6 |
| 4. Field-proven advantages | 7 |
| 5. Interfaces and UART pinout | 8 |
| 6. Configuration and operation | 10 |
| 7. Timing and event synchronisation | 11 |
| 8. Target applications | 12 |
| 9. Ordering, shipping and support | 13 |
Technical data
GNSS and positioning
| Parameter | Value | Note |
|---|---|---|
| Supported constellations | GPS, GLONASS, Galileo, BeiDou, QZSS, SBAS, IRNSS | Multi-constellation reception for reliable positioning in challenging environments |
| Positioning modes | StandAlone, DGPS, SBAS, RTK (base/rover), PPP | From single point to RTK-Fixed centimetre-level positioning |
| Frequency bands | L1 / L2 / L5 | Multi-band tracking, as stated in the product overview |
| IMU | Industrial-grade IMU with dynamic sensor fusion | Keeps heading and position usable when satellites drop out |
Interfaces, data formats and logging
| Parameter | Value | Note |
|---|---|---|
| Interfaces | Micro-USB · TTL UART · MMCX · TF card · PPS/event | Micro-USB carries two virtual COM ports plus Ethernet; multiple 3.3 V TTL UARTs; MMCX antenna; TF card slot; PPS and event I/O |
| Data formats | NMEA-0183, RTCM v2/v3, SBF | SBF convertible to RINEX, ASCII or KML for post-processing |
| Logging | TF card offline logging | Raw observations retained on board for later processing |
Timing, interference and configuration
| Parameter | Value | Note |
|---|---|---|
| Timing | Configurable 1PPS | Selectable GNSS time reference source for synchronisation |
| Interference mitigation | WBI + 3 notch filters | Wide-band interference mitigation, automatic notch filters, code and carrier-phase multipath mitigation |
| Configuration | RxControl · web UI · CLI | Web UI at 192.168.3.1, RxControl and command console; persistent boot configuration |
UART header pinout
The 20-pin header is reproduced exactly as published in the manual. Pins 1 through 10 run down the left column, 11 through 20 down the right; pins 10 and 15 are not connected on this revision.
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | EventB_3V3 | 11 | COM1_TX |
| 2 | VDD | 12 | COM1_RX |
| 3 | D- | 13 | COM2_TX |
| 4 | D+ | 14 | COM2_RX |
| 5 | ADV_M_RST | 15 | NC |
| 6 | COM3_TX | 16 | GPLED |
| 7 | COM3_RX | 17 | GND |
| 8 | COM4_TX | 18 | GND |
| 9 | EventA_3V3 | 19 | PPS0_3V3 |
| 10 | NC | 20 | COM4_RX |
Four UART ports are brought out (COM1 to COM4) alongside USB D+/D-, the event inputs, a panel-LED output and the PPS line. Signal names are the manufacturer's, including the NC entries.
Configuration and operation
The module is configured through RxControl, the built-in web UI or the command-line interface, and the configuration persists across reboots. The web UI is reached at 192.168.3.1 on the module's own network; RxControl and the command console expose the same settings and can save a configuration as the boot configuration, so a base or rover comes up in the right role after a power cut.
Base and rover roles
One board covers both deployment roles. As a local base station it broadcasts RTCM v2/v3 corrections; as a rover it consumes CORS corrections over NTRIP and reports centimetre-level RTK-Fixed positions. Because both roles share the same multi-constellation L1/L2/L5 engine, a spare unit can be moved between reference and rover without changing the integration.
Timing and event synchronisation
A configurable 1PPS output and external event triggers let position snapshots be time-stamped against GNSS time for multi-sensor alignment. The GNSS time reference source is selectable, which allows the module to be synchronised to the time base the surrounding system already uses — a ground station clock, an autopilot or a data logger — instead of imposing a new one.
Target applications
Three field deployments where the integrated IMU holds RTK-Fixed fixes when machines, vegetation or the hull block the sky.
- Construction and survey staking. One board serves as the site reference and as the stake-out rover, so the crew keeps RTK-Fixed points while machines and material block the sky.
- Telecom and ground-station timing. Configurable 1PPS and external event inputs time-stamp position snapshots against GNSS time, aligning ground-station clocks and multi-sensor logs.
- Marine and offshore survey. The IMU bridges the gaps when mast and hull hide the satellites, and raw SBF observations logged to the TF card re-process to RINEX, ASCII or KML ashore.
Ordering, shipping and support
- Shipping terms. Goods are quoted FOB Shanghai Airport. The default carrier is DHL Economy; freight is prepaid by the seller and added to the invoice, and delivery to the airport is free of charge. Air freight takes 7–10 days and express courier 3–5 working days, depending on destination and the carrier's official tracking.
- Volume discounts. Discounts are granted at the seller's discretion according to project volume; special projects and long-term partners are negotiable.
- Documentation. This page reproduces the datasheet and hardware manual; additional product data is published as machine-readable JSON alongside the product page.
Sales and technical support: sales@qumtrix.com.
Document history
| Edition | Version | Date | Notes |
|---|---|---|---|
| 202609 | 1.0 | September 2026 | First issue of the combined datasheet and hardware manual for BASE-X5A (QM5002B). Replaces all previous issues. |
Read the manual here
The full 13-page PDF, embedded. If your browser does not render it inline, use the download link below.