Qumtrix / Q.MAX5 / Hardware manual

Q.MAX5 hardware manual

Multi-band RTK GNSS module with 6-DOF IMU · Rev 1.0 · September 2026 · 12 pages

The hardware manual for the Q.MAX5 multi-band RTK GNSS module: a Septentrio Mosaic-X5 receiver, an ADI ADIS16505 six-degree-of-freedom inertial sensor, an STM32H743 host with 4 MB PSRAM cache and microSD logging for PPK, and a 3.5 V–60 V input stage. It is written for the integrator who has to mount the board, wire it into a machine's power and data harness, and get centimetre positions and valid attitude out of it. The technical data below is the manual's own; the PDF is the same document, formatted for print.

Document number
QMAX5_HW_MANUAL_1.0.DOCX
Edition
202609 · September 2026
Version
v1.0
Length
12 pages
File
PDF · 862 KB · English edition
Applies to
Q.MAX5 (Q.MAX5)

What this manual covers

The Q.MAX5 is a complete positioning receiver built around the Septentrio Mosaic-X5 engine and an ADI ADIS16505 inertial measurement unit. The manual documents the board as it ships: the GNSS and inertial performance you can design against, the processing and storage behind the raw logging, the interfaces and protocols the module exposes, and the electrical envelope it needs. It closes with the applications the module is aimed at, the local web configuration tool, power and protection behaviour, and the warranty terms.

The twelve pages run in the order an integration review usually takes: introduction, product overview and technology, technical data and specifications, what is included, target applications, quick web configuration, power and protection management, then care, maintenance and warranty. Every table from the technical-data chapter is reproduced in this page, so a specification can be checked without opening the PDF.

Key figures at a glance

ItemValue
GNSS engineSeptentrio Mosaic-X5, multi-frequency, full constellation
RTK accuracy0.6 cm + 0.5 ppm horizontal · 1.0 cm + 1 ppm vertical
PPK accuracy0.5 cm + 0.5 ppm horizontal · 0.8 cm + 1 ppm vertical
Inertial sensorADI ADIS16505-1, 6-DOF (3-axis gyroscope + 3-axis accelerometer)
Update rateUp to 100 Hz position and heading output
Input supply3.5 V min · 12 / 24 V typical · 60 V max, reverse-voltage protected
Power consumption1.8 W typical · 2.5 W max
Dimensions and weight45 × 35 × 12 mm · 32 g

Contents of the manual

Page numbers refer to the PDF edition. Each row opens the document at that page.

SectionPage
1. Introduction summary4
2. Product overview and technology5
3. Technical data and specifications6
4. What is included and key components8
5. Target applications9
6. Quick web configuration10
7. Power and protection management11
8. Care, maintenance and warranty12

Technical data

GNSS and positioning performance

ParameterValue
GNSS coreSeptentrio Mosaic-X5, multi-frequency, full-constellation receiver
ConstellationsGPS (L1C/A, L1C, L2C, L2P, L5) · GLONASS (L1CA, L2CA, L3) · Galileo (E1, E5a, E5b, AltBOC) · BeiDou (B1I, B1C, B2I, B2a, B3I) · QZSS (L1C/A, L1C, L2C, L5) · NavIC (L5)
Standalone accuracyHorizontal 1.2 m · vertical 1.9 m
RTK accuracyHorizontal 0.6 cm + 0.5 ppm · vertical 1.0 cm + 1 ppm
PPK accuracyHorizontal 0.5 cm + 0.5 ppm · vertical 0.8 cm + 1 ppm
Time to first fixCold start < 45 s · hot start < 2 s
Velocity accuracy0.03 m/s
Anti-interferenceSeptentrio AIM+ dynamic notch filtering with spoofing detection

Inertial sensor (ADI ADIS16505-1)

ParameterValue
Sensor typeIndustrial 6-DOF MEMS combination (3-axis gyroscope + 3-axis accelerometer)
Gyroscope (triaxial)Range ±125 / ±500 / ±2000 °/s · in-run bias stability 2.3 °/hr · ARW 0.13 °/√hr
Accelerometer (triaxial)Range ±78.4 m/s² (±8 g) · in-run bias stability 26.5 µm/s² (X/Y) · VRW 0.035 m/s/√hr
Sampling and outputUp to 2000 Hz internal sampling · filtered output at 100 / 200 Hz

Processing, memory and storage

ParameterValue
MCUSTM32H743VIHx · Arm Cortex-M7 at 480 MHz · 1027 DMIPS · double-precision FPU · 1 MB SRAM
System RAMESP-PSRAM32 · 4 MB external PSRAM cache (no packet loss on high-frequency streams)
Firmware storageW25Q128JVS · 128 Mbit (16 MB) NOR flash with XIP (execute-in-place)
Data loggingMicroSD card slot over SDIO for long-term raw logging for PPK post-processing

Protocols and interfaces

ParameterValue
ProtocolsNMEA 0183 v4.10 · SBF (Septentrio Binary Format) · RTCM 2.x/3.x · UBX pass-through · NTRIP client/server
UART2× UART, 3.3 V TTL, up to 921,600 bps
USB1× USB 2.0 High-Speed (Type-C / header) for the local web GUI and streaming
CAN bus1× CAN 2.0B / CAN-FD (optional onboard transceiver)
PPS output1× PPS time pulse, better than 20 ns
Antenna inputsMain GNSS + auxiliary GNSS (dual-antenna heading / moving baseline) + 2.4 GHz WiFi antenna

Electrical and physical

ParameterValue
Input supply (VIN)3.5 V min · 12 / 24 V typical · 60 V max (reverse-voltage protected)
Power managementTI TPS54260DRCR step-down · 2.5 A continuous output · Eco-mode
Power consumption1.8 W typical · 2.5 W max (RTK active + IMU streaming + SD logging)
Operating temperature−40 °C to +85 °C (industrial grade)
Dimensions (L × W × H)45 × 35 × 12 mm (PCB mainboard)
Weight32 g

Interfaces and integration

Everything an integrator needs is brought out on headers rather than hidden behind a carrier: two 3.3 V TTL UARTs up to 921,600 bps, a USB 2.0 High-Speed port that also serves the local web GUI, an optional CAN 2.0B / CAN-FD transceiver, a PPS output better than 20 ns, and the two GNSS antenna inputs the moving-baseline heading needs.

  • Dual antenna. Main and auxiliary GNSS inputs feed the moving-baseline heading solution, so heading stays valid while the platform is stationary — no magnetometer, no calibration run.
  • Raw logging. The microSD slot writes the receiver's raw observations continuously over SDIO, which is what makes PPK post-processing possible after a mission.
  • Local setup. A 2.4 GHz WiFi antenna input exposes the built-in web configuration tool; a phone or laptop joins the module directly, with no cloud account and no installer.
  • Vehicle power. The 3.5–60 V input means the board is wired straight to a 12 V, 24 V or 48 V bus; the TPS54260 stage and its protection are described under power and protection below.

What is included

  • Q.MAX5 RTK GNSS carrier mainboard
  • Septentrio Mosaic-X5 receiver core, mounted on the board
  • ADI ADIS16505-1 6-DOF inertial sensor, mounted on the board
  • MicroSD card slot for raw PPK logging
  • 2.4 GHz WiFi antenna input for local web configuration

GNSS antennas, the microSD card and the WiFi antenna itself are integration parts, not part of the shipped board.

Target applications

  1. Autonomous agriculture and ag-robotics. Tractor auto-steer, precision spraying and robotic harvesting under heavy orchard canopy, where the IMU carries the solution between satellite outages.
  2. Surveying and construction machinery. Excavator grade control and drone LiDAR or photogrammetry mapping with zero-loss PPK logging for the post-processed trajectory.
  3. UGVs and autonomous driving. Centimetre-level dead reckoning through urban canyons, tunnels and high-EMI industrial complexes.
  4. Marine and yacht navigation. Centimetre positioning and attitude for autonomous yachts and USVs through water-surface multipath and wave motion.

Local web configuration

The module is configured from a browser over its own 2.4 GHz WiFi link. Baud rates, network streams and output protocols are all set there, with no specialised software and no cloud account. For the receiver-level settings the manual defers to the official Septentrio Mosaic-X5 documentation, which remains the authoritative reference for command syntax and message definitions.

Power and protection

A TI TPS54260 step-down converter accepts 3.5 V to 60 V, so the board runs directly from 12 V, 24 V or 48 V vehicle buses without a pre-regulator. Reverse-voltage protection, over-current protection with frequency foldback and thermal shutdown are built in. Typical draw is 1.8 W with RTK active, the IMU streaming and logging to SD; the 2.5 W maximum covers the worst case of all three at once.

Care, maintenance and warranty

  • Maintenance: the Q.MAX5 module is maintenance-free.
  • Warranty: two-year manufacturer warranty; defective units are repaired or replaced free of charge.
  • Component availability: mechanical hardware components are guaranteed available for 15 years.

Repairs may only be carried out by the manufacturer or an accredited distributor. Modifications and the use of parts not sold or recommended by the manufacturer void the warranty and exclude liability, and the integration itself must follow the technical guidelines and regulations of the country of use.

Ordering and support

For quotations, sample units and integration questions, contact the Qumtrix sales team at sales@qumtrix.com. The module is supplied as the carrier board described above; antennas, cables and enclosures are quoted per project. Qumtrix also builds custom carrier variants and OEM enclosures around the same receiver and IMU pair — send the mechanical envelope and the harness you need and we will quote against it.

ItemDetail
ModelQ.MAX5
DocumentQMAX5_HW_MANUAL_1.0.DOCX · edition 202609 · version 1.0
ManufacturerQumtrix / Ennfu Scientific Company Limited, Room A411–A413, No. 99 Daxue Road, Xuzhou, Jiangsu 221116, China
Salessales@qumtrix.com

Document history

EditionVersionDateNotes
2026091.0September 2026First issue in the Qumtrix hardware-manual format. Replaces all previous issues, which are invalid.

The manual states that the information may change without prior notice; the edition and version above identify the revision this page reproduces.

Read the manual here

The full 12-page PDF, embedded. If your browser does not render it inline, use the download link below.

Download the PDF · Open in a new tab