Qumtrix / BASE-X5B / Datasheet & hardware manual
BASE-X5B datasheet and hardware manual
All-in-one industrial RTK base station board · QM3001A · Rev 1.0 · 12 pages
The datasheet and hardware manual for BASE-X5B (QM3001A), the all-in-one industrial RTK base station board. It puts a survey-grade Septentrio Mosaic-X5 core, an isolated Ethernet port running a native NTRIP server, and complete onboard power regulation on one board, so a self-hosted differential base can be deployed without a host PC, a separate network module or an extra power stage. The manual's specifications, interfaces, technical FAQ and ordering terms are reproduced on this page; the PDF is the print edition.
What this manual covers
A conventional RTK board needs an external controller, a separate network module and extra power regulation before it can act as a base station at all. BASE-X5B removes that stack. It combines a Septentrio Mosaic-X5 core, native Ethernet isolation through a Pulse H1102NL transformer, an embedded NTRIP server and complete onboard power management — a plug-and-play RTK base that starts broadcasting corrections as soon as it is powered.
Four design decisions carry the product: the positioning engine is the module rather than a host-side computation; a DC 5–15 V input with multi-stage DC-DC and LDO regulation produces clean 3.3 V and 5 V rails for 24/7 field operation; nanosecond-level PPS plus a dedicated active-antenna RF seat support GNSS and IMU fusion and time-sync gateways; and the whole assembly is a lightweight, independently deployable GNSS edge node rather than a card that needs a rack around it.
Key figures at a glance
| Item | Value |
|---|---|
| Core module | Septentrio Mosaic-X5 (Belgium original) |
| Channels | 448 parallel receiving channels |
| RTK accuracy | 6 mm + 0.5 ppm horizontal · 10 mm + 0.8 ppm vertical |
| Update rate | Up to 100 Hz, latency under 10 ms |
| Network | Isolated Ethernet (Pulse H1102NL) with native NTRIP server/client |
| Power | DC 5–15 V · 0.6 W typical · 1.1 W max |
| Operating temperature | −40 °C to +85 °C |
| Modes | RTK base · RTK rover · single point · PPP |
Contents of the manual
Technical data
| Parameter | Value | Note |
|---|---|---|
| Core module | Septentrio Mosaic-X5 (Belgium original) | Survey-grade multi-frequency GNSS RTK module for high-precision base stations and harsh industrial outdoor scenarios |
| Hardware channels | 448 parallel receiving channels | Full-band signal reception with multi-frequency observation for ionospheric and multipath suppression |
| Satellite systems | GPS, BeiDou, GLONASS, Galileo, QZSS, NavIC | Compatible with SBAS: WAAS, EGNOS, MSAS, GAGAN, SDCM |
| Frequency bands | GPS L1/L2/L5 · BeiDou B1C/B2a/B3 · Galileo E1/E5a/E5b/E6 · GLONASS G1/G2/G3 | Full-band coverage for maximum signal diversity and robust positioning |
| RTK accuracy | 6 mm + 0.5 ppm (H) · 10 mm + 0.8 ppm (V) | Centimetre-level RTK precision for high-end engineering work |
| Data update rate | Up to 100 Hz, latency under 10 ms | High-frequency output for high-speed robots and surveying |
| Operation modes | RTK base · RTK rover · single point · PPP | Switchable modes from single point to PPP precise point positioning |
| Power input | DC 5–15 V · 0.6 W typical · 1.1 W max | Ultra-wide input with onboard 3.3 V / 5 V regulated output for field, vehicle and factory deployment |
| Anti-interference | AIM+ · RAIM+ · LOCK+ | RF anti-jamming, integrity monitoring and anti-vibration tracking for continuous lock under EMI |
| Working temperature | −40 °C to +85 °C | Industrial wide temperature range for long-term outdoor operation |
Interfaces, protocols and timing
| Parameter | Value | Note |
|---|---|---|
| Interfaces | Ethernet (NTRIP) · USB-C · multi-UART · GPIO | Native Ethernet for the NTRIP server or client; USB-C for power, configuration and logs; reserved UART, PPS and GPIO for integration |
| Timing and sync | Nanosecond-level PPS output | High-precision PPS for multi-sensor time alignment and GNSS plus IMU fusion |
| Protocols | NMEA-0183 · RTCM3 · SBF · RINEX | Full industrial-standard protocol support for base and rover interoperability |
| Ethernet port | Pulse H1102NL isolated · NTRIP server/client | Industrial network isolation transformer; works directly as an NTRIP RTK base broadcasting RTCM over LAN or internet |
| USB-C | Power · configuration · firmware · logs | Power supply, parameter configuration, firmware upgrade and log export |
| Multi-UART and peripherals | TX · RX · PPS · GPIO | Reserved pins for direct connection to an MCU, data radio, sensor or robot chassis |
Core advantages
- Full constellation, multi-frequency. 448 hardware channels across GPS, BeiDou, Galileo, GLONASS, QZSS and NavIC; multi-frequency observation suppresses ionospheric error and multipath, so the board keeps lock under heavy foliage, in urban canyons and beside EMI-heavy machinery.
- Centimetre RTK at 100 Hz. 6 mm + 0.5 ppm horizontal and 10 mm + 0.8 ppm vertical, with switchable base/rover operation and PPP convergence, so one board serves both ends of a correction network.
- RF and vibration resilience. AIM+ anti-jamming, RAIM+ integrity monitoring and LOCK+ vibration-robust tracking actively mitigate RF noise, spoofed signals and mechanical vibration — the reason the fix survives machine halls, radio masts and a moving chassis.
- Native NTRIP over isolated Ethernet. The onboard Pulse H1102NL isolation transformer runs a standalone NTRIP server or client, streaming RTCM corrections to rovers, unmanned platforms and survey terminals over LAN or WAN.
- Low power, drop-in integration. Typical 0.6 W from a 5–15 V DC input with onboard 3.3 V and 5 V rails, plus NMEA-0183, RTCM3 and SBF output on a standard UART, PPS and GPIO header — into a robot chassis or a data radio with no extra power stage.
Configuration and operation
The board is configured locally in a browser: no cloud account and no software to install. Mode, stream and protocol settings are set once and persist, which is what lets a base station be commissioned at the factory or in the workshop and then deployed to a mast or a rooftop with nothing but power and a network cable.
Target applications
- Construction and machine control. A yard or site base broadcasting RTCM to every excavator, dozer and rover on site, with no dependence on mobile coverage or a third-party CORS subscription.
- Telecom and industrial timing. Nanosecond-level PPS for ground-station, substation and test-bench clocks, replacing a dedicated timing appliance.
- Marine and offshore survey. A shore base streams corrections over WAN to survey vessels and USVs, so the vessel needs neither a local radio link nor a second receiver.
Technical FAQ
What GNSS core does BASE-X5B use, and how many channels does it track?
It is built on the Septentrio Mosaic-X5 (Belgium origin), a survey-grade multi-frequency receiver with 448 parallel channels, tracking GPS, BeiDou, GLONASS, Galileo, QZSS and NavIC, with SBAS support.
What RTK accuracy and output rate does BASE-X5B deliver?
6 mm + 0.5 ppm horizontal and 10 mm + 0.8 ppm vertical, with data output up to 100 Hz at under 10 ms latency — enough for high-speed robots as well as static surveying.
Does BASE-X5B work as an NTRIP base station without extra hardware?
Yes. The onboard isolated Ethernet port (Pulse H1102NL) runs a native NTRIP server or client, so the board broadcasts RTCM3 corrections over LAN or the internet directly — no separate caster PC, and no mobile coverage needed on site.
How is BASE-X5B powered, and what does it draw?
A wide DC 5–15 V input, drawing 0.6 W typical and 1.1 W maximum, with onboard 3.3 V and 5 V regulated output for field, vehicle and factory deployment.
Which interfaces and protocols does BASE-X5B expose for integration?
Ethernet (NTRIP), USB-C for power, configuration, firmware and logs, and multi-UART pins brought out as TX, RX, PPS and GPIO for MCUs, data radios, sensors and robot chassis. Protocols: NMEA-0183, RTCM3, SBF and RINEX, plus nanosecond-level PPS for time alignment.
What temperature range and interference protection does it have?
−40 °C to +85 °C industrial operating range, with AIM+ RF anti-jamming, RAIM+ integrity monitoring and LOCK+ anti-vibration tracking for continuous lock under EMI.
Ordering, shipping and support
- Shipping terms. Goods are quoted FOB Shanghai Airport. The default carrier is DHL Economy; freight is prepaid by the seller and added to the invoice, and delivery to the airport is free of charge. Air freight takes 7–10 days and express courier 3–5 working days, depending on destination and the carrier's official tracking.
- Main markets. Europe, the Middle East, the USA and South America; shipping is worldwide.
- Volume discounts. Discounts are granted at the seller's discretion according to project volume; special projects and long-term partners are negotiable.
Sales and technical support: sales@qumtrix.com.
Document history
| Edition | Version | Date | Notes |
|---|---|---|---|
| 202609 | 1.0 | September 2026 | First issue of the combined datasheet and hardware manual for BASE-X5B (QM3001A). Replaces all previous issues. |
Read the manual here
The full 12-page PDF, embedded. If your browser does not render it inline, use the download link below.